Fitting Roller Blinds and Zebra Blinds

During the ordering process as we were asked for the control position (right, left) and fitting options (exact, recess) we will have positioned the controls and prepare the blind accordingly.

The brackets that are supplied with your blind enable you to face-fix the blind onto a wall/window frame, or top-fix the blind onto the ceiling/underside of a recess. As our Roller Blinds also comes with an Head Rail as an advantage compared to the cheap blinds in the market it is very easy to mount with only a clip to hold it in place.

              

Head Rail for the Roller Mechanism                     Angle Brackets for Face Fix and different angles

 

 

Top Fix Clip                                                                        Cassette Fixing with Angle Brackets above

 

Face Fix & Top Fix

Top Fix (to the window frame)

If you have a sound substrate to fit your blinds to the top of your window recess this does provide a neat installation where the blind is situated with minimal risk of damage in a normal situation.

  • Measure and mark the distance allowing for obstructions like handles that protrude into the recess area.
  • To calculate the spacing between the brackets, add 35mm (13/8”) to the width of the blind fabric. Hold each bracket into place and mark the hole positions. Fix the brackets so that the outsides of the brackets are this distance apart. Fit each bracket using the screws provided.
  • Brackets must be level to ensure the smooth operation of the blind.
  • Check that the rolled up fabric will not touch any surface.
  • Please ensure fixings are suitable for the wall/surface to which you are mounting the brackets.
  • Hold the blind to the brackets with the fabric hanging from the back of the blind.
  • First locate the ‘pin’ (the end of the blind opposite to the controls) into the bracket, then fix the control end into the opposite bracket. Push the blind into the bracket, depressing the plunger.
  • Allow the hook to drop downwards so that it locks into place in the bracket.

Face Fix (outside of the reveal)

You may need to face fix to get a better substrate or to avoid opening windows, handles or other obstructions. This can be done as below.

  • Hold each bracket into place and mark the hole positions.
  • To calculate the spacing between the brackets, add 35mm (13/8”) to the width of the blind fabric. Fix the brackets so that the outsides of the brackets are this distance apart. Fit each bracket using the screws provided.
  • Brackets must be level to ensure the smooth operation of the blind.
  • Check that the rolled up fabric will not touch any surface.
  • Please ensure fixings are suitable for the wall/surface to which you are mounting the brackets.
  • Hold the blind to the brackets with the fabric hanging from the back of the blind.
  • First locate the ‘pin’ (the end of the blind opposite to the controls) into the bracket, then fix the control end into the opposite bracket. Push the blind into the bracket, depressing the plunger.
  • Allow the hook to drop downwards so that it locks into place in the bracket.

 

Child Safety Device Installation

  • Children can be strangled if a safety device is not installed. Always use a safety device to keep cords or chains out of reach of children.
  • The cord retaining device must be installed at the maximum distance possible from the control mechanism to prevent looped cord(s) becoming slack.
  • Place retaining device on the wall and mark the position of the hole using a pencil. Drill holes using a suitable drill bit. Place device into position ensuring the chain is fully taut. Take the retaining device and screw it using suitable fixings ensuring the device is fully closed.

 

 

What do you need to do, Mandatory requirements?
WARNING!

Young children can be strangled by loops in pull cords, chains, tapes and inner cords that operate the product. To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around a child’s neck.

·         Move beds, cots, highchairs and playpens away from window covering cords and chains.

·         Make sure all cords and chains are always secured out of reach of babies and young children. Do not tie cords or chains together. Make sure cords or chains do not twist and create a loop

·         Move furniture away from window covering cords and chains as children love to climb.